We've unearthed this article pertaining to How to Install a Bathtub listed below on the internet and concluded it made sense to share it with you here.
Setting up a bath tub isn't precisely brain surgery, yet it does need strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old tub with a brand-new one is also a moderately challenging job. If the old bathtub is readily available, the project can relocate immediately; if you need to open up a wall to remove the old bathtub as well as position the new bathtub, the job is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly require a helper to vacate the old bathtub as well as embeded in the new one. Make certain you have actually qualified on your own for the job as well as are comfortable trying it. As opposed to working with a professional to take control of a halfway-completed project, it is better to consider employing one before you start. Possibilities are you may require an expert plumber to make tube links.
This article will aid you mount a brand-new tub in your bathroom if you have actually already purchased a brand-new bathtub and also don't require to change the setup of your previous water pipelines.
Your tools and also product checklist need to make up the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water system. After doing so, turn on the faucets to drain any type of water continuing to be in the system. The procedure of eliminating the existing taps can be rather problematic as a result of the restricted gain access to that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have been gotten rid of, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
Before moving on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic port to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin ensuring that the washing machines remain in location in between the tap as well as the sink. Protect the tap in position with the maker offered backnut. Once the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal tap adapters. The former kind must be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Tub
Using the two wood boards under its feet, position the tub in the called for position. The wooden boards are helpful in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by examining the level and readjusting the feet on the bathtub until the level reads degree.
To install faucets, fit the bottom of the outermost flexible tap port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Activate the supply of water as well as examine all joints and also brand-new pipework for leaks and also tighten them if necessary. Fill up the tub and also inspect the overflow outlet and the normal outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the maker's instruction manual. Tiling and also securing around the bath tub must wait up until the bathtub has been made use of at least once as this will resolve it right into its last setting.
Preparing for the Installment
First of all, the sustaining framework provided with the bath must be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps device to stop pressure on the tub.
Fit the adaptable faucet connectors to the bottom of both faucets making use of 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be suited its final position.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to break a stiff seal, creating the water to penetrate the wall between the bathroom and also the tiling, causing difficulties with moisture as well as possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your components and also installations. They are sold in tubes and also cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly load the tub with water prior to sealing, to allow for the movement experienced when the tub is in usage. The sealer can crack relatively early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally conveniently readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very fascinated with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I am assuming you appreciated my piece. Sharing is good. You just don't know, you will be doing someone a favor. I enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Expertise at your service.